H&C Concrete

Product Supplies

1. Stiff broom
2. Nylon/polyester brush
3. Soft woven roller cover, 3/8" - 1/2" nap
4. Roller frame
5. Paint tray/liner
6. Airless Sprayer

   Pressure: 1500 psi
   Tip: .013" - .017"  

   Conventional Sprayer

   Air Pressure: 30 - 50 psi
   Fluid Pressure: 15 - 20 psi

   Cap/Tip: 704/FX or equivalent

   High-Volume Low Pressure Sprayer Cap/Needle: Titan #3 or equivalent

Product Preparation

Due to a wide variety of substrates, preparation and application methods and environments, test the product in an inconspicuous spot for adhesion and compatibility prior to full scale application.  All surfaces must be clean, dry and free of grease, oil, paint, sealers, etc. 

Newly poured concrete must cure for at least 45 days.  Concrete must be etched with H&C Concrete Etching Solution, follow label instructions. Surface should feel like 120-grit sandpaper, if not, then etch again.  Allow 24 hours to dry prior to staining. 

Asphalt:  must be free of dirt, oil, grease, wax etc.  Scrub with H&C Cleaner Degreaser, following label instructions.  DO NOT ETCH ASPHALT. We do not recommend staining if asphalt has been freshly sealed. 

Previously painted: all old, peeling or flaking paint must be removed.  Areas with firm adhesion must be clean and free of dirt, oil grease etc.  Clean with H&C Cleaner Degreaser, following label instructions.  Rinse thoroughly and allow to dry.  The remaining paint/coating should be rough sanded in a circular motion to ensure adhesion of H&C Concrete Stain Solid Color Water-based.  Rinse away sanding dust.

Product Application

*Air and surface temperature should be between 50 and 90°F.  If the surface temperature exceeds 90°, spray a fine mist of water to reduce the temperature.  Rain should not fall for 24 hours after application. Apply H&C Concrete Stain Solid Color Water-Based to dry or even slightly damp surfaces.

*Intermix all containers together to ensure color uniformity.

For bare concrete, thin your first coat with one pint of water per gallon of stain.  You do not need to do this step for asphalt, previously painted or vertical surfaces. 

Apply first coat evenly, working in one direction. Allow to dry at least 2 hours before applying the second coat.  Apply the second coat in the opposite direction to the first coat. Two coats are usually sufficient.  Consider using H&C Sharkgrip Slip-Resistant Additive to the final coat. 

Dry to the touch: 30 minutes

Light traffic and recoat time: 2 hours

Heavy traffic/vehicular: 72-96 hours

Product Supplies

1. Stiff broom
2. Natural bristle paint brush
3. Soft-woven roller cover 3/8" - 1/2" nap, or other solvent-resistent cover
4. Roller frame
5. Paint tray
6. Xylene for cleanup
7. Optional: airless sprayer (pressure 1500 psi, tip: .013"- .017"), Conventional Sprayer (air pressure 30-50 psi, cap/tip: 704/FX or equivilant). Be sure to back roll after airless sprayer to work the product smoothly and evenly into the surface.

Product Preparation

Due to a wide variety of substrates, preparation and application methods and environments, test the product in an inconspicuous area for adhesion and compatibility prior to full scale application.  All surfaces must be clean, dry and free of grease, oil, paint, sealers etc.  Use H&C Cleaner Degreaser following the label directions, rinse thoroughly and allow the surface to dry. 

New concrete must cure for 45 days.  All horizontal concrete (new or old), must be etched with H&C Etching Solution first for proper adhesion, follow label instructions carefully. For very smooth, or highly troweled surfaces with little or no porosity, use H&C Etching Solution at full strength.  Do not etch painted surfaces, the previous coating must be removed prior to applying H&C Concrete Sealer Solid Color Solvent-based. 

For the best waterproofing protection, patch and repair cracks and crevices where water can enter.  On floor surfaces, use appropriate patching material, but keep in mind that patching compounds will generally be visible through clear coatings. 

Product Application

*Apply under dry conditions only!  Do not apply if rain is expected within 12 hours following application.

*Air and surface temperature should be between 50° and 90° during application and for 24 hours following. 

Sweep the surface with a broom immediately prior to applying, to ensure no foreign substances or particles have fallen on it.  Stir thoroughly before and during application.  Do NOT reduce H&C Concrete Sealer Solid Color Solvent-based. 

If you need to "cut in" the corners or edges, do that first with your brush.  Use your roller to evenly apply the remainder of the surface, working in one direction.  Do not overwork the product - brushing or rolling back over partially dried material may cause lifting of the coating from the surface. 

Allow the product to dry 12 hours before applying the second coat (if necessary).  Again, being careful not to overwork the product, apply in the OPPOSITE direction of the first coat (perpendicular).

Dry to the touch: 15 minutes

Foot Traffic in 1 hour

Recoat: 12 hours

Heavy Traffic:  72 - 96 hours

Product Supplies

1. Roller Cover 3/8" nap (soft woven)
2. Paint brush
3. Paint tray
4. Roller frame
5. Extension pole
6. Stiff broom
7. Water source / hose to thoroughly clean surface
8. H&C® Cleaner Degreaser (if necessary)
9. H&C® Etching Solution (if necessary)

Product Preparation

All surfaces must be clean, dry and free of grease, oil, paint, sealers etc.  Use H&C Cleaner Degreaser following the label directions, rinse thoroughly and allow the surface to dry. 

New concrete must cure for 45 days.  All horizontal concrete (new or old), must be etched with H&C Etching Solution first for proper adhesion, follow label instructions carefully. For very smooth, or highly troweled surfaces with little or no porosity, use H&C Etching Solution at full strength.  Do not etch painted surfaces, the previous coating must be removed prior to applying H&C Low VOC Concrete Sealer Solid Color Solvent-Based.

Product Application

*Apply under dry conditions only!  Do not apply if rain is expected within 12 hours following application.

*Air and surface temperature should be between 50° and 90° during application and for 24 hours following. 

Sweep the surface with a broom immediately prior to applying, to ensure no foreign substances or particles have fallen on it.  Stir thoroughly before and during application.  

If you need to "cut in" the corners or edges, do that first with your brush.  Use your roller to evenly apply the remainder of the surface, working in one direction.  Do not overwork the product - brushing or rolling back over partially dried material may cause lifting of the coating from the surface. 

Allow the product to dry 12 hours before applying the second coat (if necessary).  Again, being careful not to overwork the product, apply in the OPPOSITE direction of the first coat (perpendicular).

If a clear coat is desired, use H&C Low VOC Concrete Sealer Clear Gloss Solvent-based; this clear coat is designed to go over the Low VOC solid color sealer and will ensure a long lasting color and finish for years to come.

Dry to the touch: 15 minutes

Foot Traffic in 1 hour

Recoat: 12 hours

Heavy Traffic:  72 - 96 hours